Intec 50013-00 Installationsanleitung PDF herunterladen

Operation and Safety Guide

Model #’s 50004-00 & 50013-00

Vendor Website: www.inteccorp.com Support Phone No. 800-666-1611

See operational video at http://www.inteccorp.com/fiberforce/

Tool Operation:

Step

Action

1

Unload machine using safe lifting techniques. Secure hopper base with

the four fasteners. Note: Match key slot in base to that of hopper for

proper alignment & operation. Position machine in a dry, hazard free

environment to allow for suitable material feed and electrical power

access. Sweep hand across the filter to clean any foreign materials.

2

Ensure that all panel switches are in the off position. Using the twist

lock power cord supplied, plug the machine into a dedicated 115V

15amp or 20amp circuit.

3

Install the 2-50’ 2-1/2” hose sections. The section with the male &

female adaptor goes on the machine first. The other section with the

remote plugs into the first hose. Ensure that the retainer snaps into

place to prevent hose blow-off.

4

Open the material feed gate by removing the locking pin. Attics: pull

slide gate outward to the last hole position, and secure gate by placing

pin in the last hole. Walls: Refer to the owner’s manual or Intec’s

website for proper settings.

5

Ensure the GFCI is reset, reset the agitator circuit breaker & turn on

the main circuit breaker. The white ‘ready light’ on the side of the

machine will illuminate. Note: if the white light does not come on,

ensure that the hopper is properly positioned with the opening above

the circuit breakers.

6

Undo the strap securing the hopper door / loading platform. Lift up on

the door slightly and pull forward into the loading position. Directions

for loading the machine are printed on the loading platform.

7

Caution: Never let the plastic packaging enter the hopper.

Caution: Never push down on insulation when in hopper.

Fiberglass: Cut bag of insulation in half. Place open end of ½ bag to

the left or right side of the loading platform. Slice plastic with cutting

tool and let insulation expand into hopper.

Cellulose: Remove packaging. Place cellulose bale into hopper.

8

Hose operator takes the hose to the location for insulation blowing.

Use the remote to turn machine on to blow insulation material. Hopper

Operator continues to feed material into hopper until job is complete.

9

At completion, use the remote or panel switch to turn machine off.

Remove any insulation still in the system. Return machine, two hose

sections, and power cord to the rental center.

SAFETY TOPICS:

To avoid personal injury, do not attempt to operate this

equipment until you thoroughly read and completely

understand the operator’s manual. Please visit

http://www.inteccorp.com/fiberforce/

for additional

information.

SAFETY CHECKLIST:

1) Read all the instructions before using the insulation

blower.

2) To reduce the risk of injury, close supervision is necessary

when an insulation blower is used near children.

3) Do not contact moving parts.

4) Only use attachments recommended or sold by the

manufacturer.

5) Use of Extension and Power Cord:

a) This product requires the use of a power cord. In

addition to the supplied power cord, care should be

exercised in the selection and use of an extension

cord.

b) The extension cord shall be a grounded 3-wire cord.

c) The extension cord should be arranged so that it will

not drape over the countertop or tabletop where it can

be tripped over, snagged, or pulled on unintentionally

(especially by children).

d) An outdoor rated extension cord should be used with

this machine. An outdoor- use extension cord is

marked with suffix letter “W” and with a tag stating

“Suitable for Use with Outdoor Appliances.”

e) The marked electrical rating of the extension cord

shall be rated for at least 15 amps.

f) To unplug or disconnect: Put the blower and agitator

control panel and remote buttons in the stop position

before removing plug from outlet.

g) Do not unplug by pulling on the power cord. To

unplug, grasp the male and female plugs and pull

apart.

h) Unplug from outlet when not in use and before

servicing or cleaning.

i) Do not operate any insulation blower with a damaged

cord or plug, or after the machine malfunctions or is

dropped or damaged in any manner.

6) In the case of a non-operable or malfunctioning blower,

return the insulation blower to the nearest authorized

service facility for examination, repair, or electrical or

mechanical adjustment.

7) Store insulation blower indoors when not in use. Keep out

of the reach of children

8) Never operate this equipment if the operator or the

machine is standing in water, snow or rain. Do not clean

this insulation blower with water spray or the like.

9) Connect to a properly grounded outlet only.

10) Wear long sleeve shirt, gloves, a hat, safety glasses or

goggles, and a nose & mouth dust mask.

WARNING:

1) Never reach into the hopper when system is operating.

2) Keep all foreign materials out of hopper.

3) Stop all motors and disconnect power cord before

attempting to remove a foreign object or jam.

4) Never point insulation hose in direction of people or pets.

Intec 50013-00 Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach Lüfter / Trockner Intec 50013-00 herunter. Intec 50013-00 Installation Guide Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern